Specialty Extinguishers
Click on Tab Bar of Choice
For Sensitive non-residue clean Electronic fire protection.
IT/Computer rooms, High Value protection and Aviation.
These extinguishers are rated for A, B & C Fire Hazards. *Although Halon 1211 Gas is no longer produced, Halon 1211 Gas is available for recharging existing Halon 1211 extinguishers using "Recycle "Non-Virgin" gas, compliant to EPA Protocals. Call us for your Halon recharging needs.
Clean Guard/FE-36 extinguishers non-residue/clean agent extinguishers can also be another alternative for the customer. These units have similar fire fighting capabilities as Halotron.
Offer clean agent fire protection for Class "B" & "C" fire hazards.
Standard Dry Chemical/Sodium Bicarbonate For Class "B" and Class "C" type fires. Can be used for fire fighting training programs, garages, vehicles, marine and aviation applications.
Potassium Bicarbonate Dry Chemical for Class "B" and Class "C" type fires. This is the most effective type of dry chemical available for Class "B" flammable liquid type fires. Can be used for garages, service bays, marine, vehicle, fuel storage, and fuel transfer areas.
For High Hazard Pressurized Flammable Liquid & Gas Fires, offering a rapid fire knock down at 1 pound per second discharge rate.
For all Cooking Operations / hot grease, animal fats, vegetable oil, fire hazards.
Are for use to Extinguish Class "A" (Paper, Wood, or Textile) Fires, offering the soaking/quenching effect of a liquid for Class A Hazards.
Offer clean agent fire protection for Class A, paper, wood and textile fires along with Non-Conductive Capability for Class "C" Electrical Fires for Computer Rooms and other High Value equipment.
Provides extinguishment & vapor barrier spill protection for many types of Class "A" & Class "B" Flammable Liquid type Hazards.
Automatic Clean Agent & Dry Chemical Extgs. For Total Flood & Spot 24/7 Fire Protection for rooms up to 3000 cubic feet in size.
For Burning Metal Fire Hazards.
Halotron I Clean Agent Extinguishers
Halotron I fire extinguishers provide "Clean Agent" fire protection that leaves no residue for sensitive electronics or similar High Value fire protection requirements. Halotron I is discharged as a rapidly evaporating liquid. Its relatively high boiling point of 80.6°F (27°C) gives it an advantage over other clean extinguishing agents, which tend to have lower boiling points and therefore evaporate sooner, limiting their chemical agent throw length on to the fire and overall effectiveness for the non-expert firefighter.
FEATURES:
• Stored Pressure Design
• Dependable Drawn Steel Cylinders
• Durable High Gloss Polyester Powder Paint
• All Metal Valve Construction
• Temperature Range -40°F to 120°F
​
ENVIRONMENTALLY ACCEPTABLE
• EPA approved “Clean Agent” for Class A, B & C hazards
• Low GWP (Global Warming Potential)
• Low ODP (Ozone Depletion Potential)
• Short Atmospheric Half-Life
• CLEAN Leaves No Residue
These extinguishers are FAA Approved.
USER FRIENDLY
• Maximum Visibility During Discharge
• Large Loop Pull Pin
• No Electrical Conductivity Back to the Operator
• No Thermal or Static Shock
Usage Examples for Halotron Extgs:
-
I.T. / Computer type fires that will not leave residue, conduct electricity, and offer minimal clean-up.
-
Halotron extgs. offer "Non-Residue" fire protection for other High Value items, such as Antique Automobile or Marine Storage.
Clean Guard/FE- 36 Fire Extinguishers
Clean Guard/FE-36 extinguishers non-residue/clean agent extinguishers can also be another alternative for the customer. These units have similar fire fighting capabilities as Halotron.
CO2 Carbon Dioxide Extinguishers
Carbon Dioxide (CO2) Compressed Gas Fire Extinguishers offer clean agent fire protection for Class B (Flammable Liquid fires) and Class C (Energized Electrical fires). These units are economical to recharge and displace the oxygen along with a cooling effect at minus 40 degrees F, breaking the fire chain. CO2 extinguishers have a limited range, especially outdoors and if the working fire is producing a lot of heat, the operator may not be able to extinguish the fire at close range. *Other clean agent extinguishers should be considered, such as Halotron or Halon 1211.
Standard Dry Chemical Fire Extinguishers
Standard (BC) Dry Chemical Fire Extinguishers are Sodium Bicarbonate Based and offer a Neutral Fire Fighting Agent that is Non-Toxic and Non-Corrosive. Standard (BC) Dry Chemical Fire Extinguishers are rated for Class B Flammable Liquid Hazards and Class C Energized Electrical Hazards. * Note: Standard Dry Chemical Extinguishers are NOT rated for Class A (Paper, Wood, Or Textile Fires).
Typical Uses: Flammable Liquid (Class B) And Energized Electrical (Class C) Hazards​​.
-
Offices
-
Classrooms
-
Places of Worship
-
Parking Garages
-
Hotel/Motel Assembly Halls
-
Guest Areas
-
Retail Stores
-
Light Manufacturing Facilities
-
Research Facilities (Without Sensitive Electrical Equipment)
-
Auto Dealerships
-
Vehicle/Marine Service Centers
-
Aviation / Aircraft Servicing
Purple-K Dry Chemical Extinguishers
Typical Uses: Flammable Liquid (Class B) and Energized Electrical (Class C) Hazards
Purple - K (Potassium Bicarbonate) Dry Chemical Fire Extinguishers are rated for Class B Flammable Liquid Hazards & Class C Energized Electrical Hazards.
Purple - K Fire Extinguishers offer the Best Fire Fighting Capability for Flammable Liquid Fires over ABC & Standard (BC) Units.
Purple - K Fire Extinguishers can be corrosive when fighting fires where moisture or water is present.
-
High Hazard Flamable Liquid Storage Facilities
-
Fuel Depots
-
Vehicle Repair Bays
-
Gasoline Stations
-
Marine Service Facilities
High Flow Dry Chemical Fire Extinguishers
High Flow Category Dry Chemical Fire Extinguishers Are designed to deliver high - flow fire extinguishing chemical agents at a higher discharge rate of 1 lb per second. over normally rated extinguishers. These Extinguishers are mandatory for industrial and similiar applications where hazards such as Pressurized Flammable Liquids, Pressurized Gas, or 3 - Dimensional Fires exist. These extinguishers are available in ABC, BC, & Purple-K Dry Chemical Models.
These Extinguishers are available in both Standard or Heavy Duty Models.
Available in:
-
ABC Dry Chemical
-
BC (Standard) Dry Chemical
-
Purple - K Dry Chemical
Class K Wet Chemical Kitchen Fire Extinguishers
Wet Chemical extinguishers are designed specifically for kitchen grease fire hazards and meet the new Class "K" listing now required for all extinguishers installed in Restaurant Kitchens and similar Cooking Operations. Note: Prior to 1998, Standard dry chemical and Purple-K extinguishers were used to put out kitchen type fires. These extinguishers did allow for Fire Reflash and have now been replaced under the 1998 Class K fire protection classification. Class K Wet Chemical Fire Extinguishers are rated for Class A and B fires in sizes ranging from 6 liters to 2.6 gallons.
Pressurized Water Extinguishers
Pressurized Water Extinguishers are for use to Extinguish Class A (Paper, Wood, or Textile) Fires. Although ABC Dry Chemical Extinguishers have the capability to put out Class A Fires, liquid type water extinguishers offer a Quenching / Soaking effect for Multi - Level / Deep Seated Fires. We also offer a Wetting Agent that can be added to the water extinguisher which provides for deeper saturation for deep seated hazards. Because of their Stainless Steel, Non-Metallic construction, our Pressurized Water Extinguishers can be used in a Hospital/Medical setting. This includes X-Ray and MRI equipment.
Water Mist Fire Extinguishers
The Water Mist unit uses deionized water and incorporates a spray wand nozzle. These features make it safe for use on energized electrical equipment. Water Mist is considered to be the #1 extinguisher choice for libraries and hospitals. 2.5 Gallon Pressurized Water Mist Fire Extinguishers: These Units offer Class A (paper, wood, and textile) fire protection as well as Safe Class C Electrical Fire protection up to 100,000 volts. The extinguisher is equipped with a non-conductive discharge hose/and wand assembly which insulates the operator from electrical shock. These water mist units can be used in and around electrical equipment. These extinguishers can be used for I.T. / Computer type fires that will not leave residue, or conduct electricity, and offers minimal clean-up.
AFFF Foam Fire Extinguishers
Class A & B extinguisher: AR-AFFF (Alcohol Resistant Aqueous Film Forming Foam) Light Water Fire Extinguishers offer excellent fire protection for Class A & B flammable liquids. 3-M developed AFFF Light Water that offers superior Foam Extinguishment over the older style protein foam agents. The Light Water Foam allows the foam agent to float on top of the flammable liquid. These units not only extinguish a Class A fire, but applied to a non-ignited Class B flammable liquid spill, it will seal the surface forming a vapor barrier, minimizing the chance of serious fire re-flash. Ideal for emergency first response vehicles along with industrial application usage. Easy and effective application with air aspirated nozzle. The Alcohol Resistant fire fighting agent is effective on fires in a wide variety of Class B materials such as alcohols, polar solvents, hydrocarbons and combinations such as gasohol, along with an excellent Class A paper, wood, and textile capability.
Automatic Clean-Agent Fire Extinguishers for Specific Hazard Fire Protection
Total Flood and Spot Protection at a reasonable cost for 24/7 fire protection. Usage examples: IT/computer rooms, telephone equipment rooms, backup file rooms, and vaults. These units can be hung or mounted from the ceiling of the area to be protected to provide 24/7 fire protection at a lower cost compared to other clean agent automatic suppression systems. These automatic extinguishers can be equipped with a factory installed pressure switch to allow for automatic shut down of electric equipment, send a signal to a fire or security alarm panel or activate a local alarm device to alert your employees. In addition we offer SEVO Systems Novec Clean Agent Suppression Systems for Larger Areas to be Protected.
Class D Dry Powder Extinguishers
CLASS D DRY POWDER FIRE EXTINGUISHER FOR BURNING METAL HAZARDS are specifically designed for use on combustible metal fires. They feature a discharge assembly that keeps the operator at a safe distance while providing accurate application of the agent onto the fire. From the heat of the fire, the sodium chloride based agent forms a crust to exclude air from the burning material. Suitable for use on Class D fires such as those involving magnesium, sodium, potassium and sodium-potassium alloys. There is data showing that zirconium, uranium, titanium, and powdered aluminum fires can be controlled and extinguished with this unique extinguisher as well. For Lithium based fires we also offer Class D "Copper" Dry Powder extinguishing agent.
We also offer Class "D" Copper Chemical Powder available for Lithium based metal fire hazards.
​
For some cool answers to your hottest fire/safety questions, give us a call at Five Star Fire Protection Services.
Halon 1211 Pressure Gas Fire Extinguishers
Halon 1211 Pressure Gas clean agent fire extinguishers offer excellent fire fighting protection for Class B (Flammable Liquids) and Class C (energized electrical) hazards. In their larger sizes, Halon 1211 offers a Class A (Paper, Wood & Textile) capability as well. Although Halon 1211 is no longer produced because of their ozone depleting qualities, they can be recharged & serviced under current EPA Protocols using Recycled, Non-Virgin Halon 1211 Gas. Halon 1211 extinguishers have the best fire fighting ratings to extinguish fires, over all of the other clean agents available in the fire equipment marketplace.